Difference between revisions of "Logbook MirrorInstall"
(→Enter comments in reverse time order) |
|||
| Line 6: | Line 6: | ||
|- valign="top" | |- valign="top" | ||
| + | |- | ||
| + | | 2018-05-03 ||Koji, Tomohiro, Casana || Mirror Installation || We finished to install 15 mirrors on the structure (in total 59).<br>|| | ||
| + | [[File:MirrorInstallation20180504.jpg|200px|Image: 200 pixels]] | ||
|- | |- | ||
| 2018-05-03 ||Koji, Tomohiro, Casana || Mirror Installation || We finished to install 15 mirrors on the structure (in total 59).<br>We found one CMOS camera whose mirror was already installed last time. Its coordinate is (+1,+3). After we found it, we asked Uwe(CaSana) to change wrong one to correct one for the mirror in (+1,+3) and they did successfully. They told us that the mirror in (+1,+3) was with the CMOS camera for (1,-3) mistakenly. || | | 2018-05-03 ||Koji, Tomohiro, Casana || Mirror Installation || We finished to install 15 mirrors on the structure (in total 59).<br>We found one CMOS camera whose mirror was already installed last time. Its coordinate is (+1,+3). After we found it, we asked Uwe(CaSana) to change wrong one to correct one for the mirror in (+1,+3) and they did successfully. They told us that the mirror in (+1,+3) was with the CMOS camera for (1,-3) mistakenly. || | ||
| + | [[File:MirrorInstallation20180503.jpg|200px|Image: 200 pixels]] | ||
|- | |- | ||
| 2018-04-28 || Satoshi, Tomohiro, Casana || Mirror Installation || We finished to install 12 mirrors on the structure (in total 44).<br>Casana people inside the dish dropped one O-ring while removing actuator caps.<br>Once by mistake we assembled a wrong combination of a CMOS and a mirror. We noticed that when we were putting the assembled one on the cradle. We should always be careful for the combination. || | | 2018-04-28 || Satoshi, Tomohiro, Casana || Mirror Installation || We finished to install 12 mirrors on the structure (in total 44).<br>Casana people inside the dish dropped one O-ring while removing actuator caps.<br>Once by mistake we assembled a wrong combination of a CMOS and a mirror. We noticed that when we were putting the assembled one on the cradle. We should always be careful for the combination. || | ||
Revision as of 15:14, 4 May 2018
Enter comments in reverse time order
| Date | Who did it? | Action | Comments | Documents |
|---|---|---|---|---|
| 2018-05-03 | Koji, Tomohiro, Casana | Mirror Installation | We finished to install 15 mirrors on the structure (in total 59). |
|
| 2018-05-03 | Koji, Tomohiro, Casana | Mirror Installation | We finished to install 15 mirrors on the structure (in total 59). We found one CMOS camera whose mirror was already installed last time. Its coordinate is (+1,+3). After we found it, we asked Uwe(CaSana) to change wrong one to correct one for the mirror in (+1,+3) and they did successfully. They told us that the mirror in (+1,+3) was with the CMOS camera for (1,-3) mistakenly. |
|
| 2018-04-28 | Satoshi, Tomohiro, Casana | Mirror Installation | We finished to install 12 mirrors on the structure (in total 44). Casana people inside the dish dropped one O-ring while removing actuator caps. Once by mistake we assembled a wrong combination of a CMOS and a mirror. We noticed that when we were putting the assembled one on the cradle. We should always be careful for the combination. |
|
| 2018-04-27 | Martin, Satoshi, Tomohiro, Casana | Mirror Installation | We finished to install 16 mirrors on the structure (in total 32). Casana people inside the dish dropped a hexagonal key. It was later found on the catwalk below them. We were not sure if people inside the dish unscrew milling parts to straighten actuators and fix the milling parts again. Martin went inside the dish and checked that they are doing these works for all the mirrors. |
|
| 2018-04-26 | Martin, Satoshi, Tomohiro, Casana | Mirror Installation | We started the mirror installation at Roque. We finished to install 15 mirrors on the structure (in total 16). | 
|
Trouble Shooting
- 2018/04/28
- While inserting a safety bolt, we damaged a little the edge of the hole. We kept this mirror today and will attach silicon paint the next working day.
- We found one fixed point which has one hole just above a sticking part of the hose band. We replaced with a new fixed point as we could not insert a bolt to that hole.
- 2018/04/26
- When Casana people tried to install one mirror, they realized a big nut did not fit the fixed point and they could not fix the fixed point. It may have happened in the dish when trying to fix the nut. We solved this problem quickly by replacing the fixed point with a new one. Still, we check if a nut fits well a fixed point of a mirror to be installed before attaching it to the cherry picker.
- Sometimes it is very hard to insert safety bolts because of glue and a tape inside the hole. We solved by using a small hammer and a small screwdriver which Holger suggested to us to use to remove glue or tape.
