Difference between revisions of "Logbook MirrorInstall"
(→Trouble Shooting) |
|||
| Line 7: | Line 7: | ||
|- valign="top" | |- valign="top" | ||
|- | |- | ||
| − | | 2018-04-28 || Satoshi, Tomohiro, Casana || Mirror Installation || We finished to install 12 mirrors on the structure (in total 44). || | + | | 2018-04-28 || Satoshi, Tomohiro, Casana || Mirror Installation || We finished to install 12 mirrors on the structure (in total 44). Casana people inside the dish dropped off one O-ring while removing actuator caps. Once by mistake we assembled a wrong combination of a CMOS and a mirror. We noticed that when we were putting the assembled one on the cradle. We should always be careful for the combination.|| |
[[File:MirrorInstallation20180428.jpg|200px|Image: 200 pixels]] | [[File:MirrorInstallation20180428.jpg|200px|Image: 200 pixels]] | ||
|- | |- | ||
| − | | 2018-04-27 || Martin, Satoshi, Tomohiro, Casana || Mirror Installation || We finished to install 16 mirrors on the structure (in total 32). || | + | | 2018-04-27 || Martin, Satoshi, Tomohiro, Casana || Mirror Installation || We finished to install 16 mirrors on the structure (in total 32). Casana people inside the dish dropped off a hexagonal key and could not find it on the ground. We are not sure if people inside the dish unscrew milling parts for actuators, make actuators straight and fix the milling parts again. Martin went inside the dish and checked that they are doing these works for all the mirrors.|| |
[[File:MirrorInstallation20180427.jpg|200px|Image: 200 pixels]] | [[File:MirrorInstallation20180427.jpg|200px|Image: 200 pixels]] | ||
|- | |- | ||
| Line 20: | Line 20: | ||
== Trouble Shooting == | == Trouble Shooting == | ||
2018/04/28 | 2018/04/28 | ||
| − | |||
| − | |||
- While inserting a safety bolt, we damaged a little the edge of the hole. We kept this mirror today and will attach silicon paint the next working day. | - While inserting a safety bolt, we damaged a little the edge of the hole. We kept this mirror today and will attach silicon paint the next working day. | ||
- We found one fixed point which has one hole just above a sticking part of the hose band. We replaced with a new fixed point as we could not insert a bolt to that hole. | - We found one fixed point which has one hole just above a sticking part of the hose band. We replaced with a new fixed point as we could not insert a bolt to that hole. | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
2018/04/26 | 2018/04/26 | ||
Revision as of 09:32, 1 May 2018
Enter comments in reverse time order
| Date | Who did it? | Action | Comments | Documents |
|---|---|---|---|---|
| 2018-04-28 | Satoshi, Tomohiro, Casana | Mirror Installation | We finished to install 12 mirrors on the structure (in total 44). Casana people inside the dish dropped off one O-ring while removing actuator caps. Once by mistake we assembled a wrong combination of a CMOS and a mirror. We noticed that when we were putting the assembled one on the cradle. We should always be careful for the combination. |
|
| 2018-04-27 | Martin, Satoshi, Tomohiro, Casana | Mirror Installation | We finished to install 16 mirrors on the structure (in total 32). Casana people inside the dish dropped off a hexagonal key and could not find it on the ground. We are not sure if people inside the dish unscrew milling parts for actuators, make actuators straight and fix the milling parts again. Martin went inside the dish and checked that they are doing these works for all the mirrors. |
|
| 2018-04-26 | Martin, Satoshi, Tomohiro, Casana | Mirror Installation | We started the mirror installation at Roque. We finished to install 15 mirrors on the structure (in total 16). | 
|
Trouble Shooting
2018/04/28
- While inserting a safety bolt, we damaged a little the edge of the hole. We kept this mirror today and will attach silicon paint the next working day.
- We found one fixed point which has one hole just above a sticking part of the hose band. We replaced with a new fixed point as we could not insert a bolt to that hole.
2018/04/26
- When Casana people tried to install one mirror, they realized a big nut did not fit the fixed point and they could not fix the fixed point. It may have happened in the dish when trying to fix the nut. We solved this problem quickly by replacing the fixed point with a new one. Still, we check if a nut fits well a fixed point of a mirror to be installed before attaching it to the cherry picker.
- Sometimes it is very hard to insert safety bolts because of glue and a tape inside the hole. We solved by using a small hammer and a small screwdriver which Holger suggested to us to use to remove glue or tape.
